Contact Us Today
Toll-FREE

Refurbished OEC 9800 C-arm

Refurbishing Process:
All OEC-9800’s go through a multistep refurbishing process. Each unit is restored to a like-new status. Pain Management, Orthopedics and Rehabilitation Services are just a few of the applications utilizing the refurbished OEC-9800 c-arm. The rotating x-ray tube allows for greater penetration and resolution for the lumbar area when doing needle localizations or other work involving the thicker anatomical areas of patients. For barium swallows a VCR or Digital Video Recorder can be utilized for better record keeping and post study analysis. The 1K X 1K CCD Technology used in the OEC-9800 image system allows for crisp, clear imaging. Whatever the purpose, a refurbished OEC-9800 will deliver the results you can depend on.

Mechanical repairs/cosmetic maintenance

  • All defective parts and covers are repaired or replaced
  • C-arm is completely disassembled and repainted
  • “C” is removed from main frame assembly
  • Horizontal arm removed, inspected and repaired as necessary
  • Vertical column removed and bearings removed inspected and replaced as required
  • X-ray tube removed and inspected for artifacts and internal integrity
  • Image intensifier removed and inspected for any imperfections and grid integrity
  • Camera removed
  • Wheels removed, cleaned and or replaced from main chassis
  • Chassis inspected for structural defects and repaired as necessary
  • Vertical lift assembly is tested for drift and adjusted/replaced if necessary
  • All bearings are inspected, cleaned and re-lubricated, or replaced as needed
  • Control panel display is tested and replaced if necessary
  • All wheels are inspected and lubricated and/or replaced as needed, with new cable pushers installed
  • All locks and brake assemblies are inspected, cleaned, and repaired or replaced as needed
  • C-arm is completely disassembled and repainted
  • Steering is tested and adjusted is required
  • Foot switch and hand switch provided on each unit
  • A complete set of operator and service manuals are provided

Re-assembly

  • All components sent to C-arm reassembly area for rebuilding
  • “C”, Image tube and camera, Vertical column, main control and power cable installed
  • New batteries are installed
  • New CRT monitors installed in monitor cart
  • Monitor cart rebuilt
  • When C-arm is completely rebuilt mechanically system is sent for calibration and final testing

Testing/calibration

  • Image intensifier and X-ray tube are tested for stability and balance
  • Image intensifier is tested for resolution and gain to be within OEM specifications
  • X-ray tube bearings are tested for noise and coast time
  • X-ray tube filaments and stator windings are tested
  • X-ray tube radiation output is verified to be within OEM specifications
  • X-ray generator high voltage tested
  • Maximum dose rate is set in compliance with government regulations
  • CCD camera calibrated to OEM specifications
  • X-ray beam is aligned for each field size
  • C-arm is tested for current leakage requirements
  • All monitors are aligned, resized, centered and focused
  • All monitors are adjusted for brightness and linearity
  • Video system is optimized for gray scale and resolution
  • All power supplies are tested and calibrated or replaced as necessary

Specifications:
Technical Specificaitons Generator

  • High frequency generator 15kW full-wave
  • Up to 120 KVP and 75MA for radiographic exposures
  • Continuous fluro-mode up to 20 mA
  • One shot frame integration (low, medium, high)
  • Full power from standard 110V 15A Or 220V 8A outlet
  • Patented energy buffer design X-Ray Tube
  • Rotating anode X-ray tube
  • Focal spots: 0.3 - 0.6 mm
  • 300,000 HU Anode heat capapcity

Physical Specificaitons

  • Free Space in Arc - 31”
  • Depth of Arc: 26”
  • Arc orbital movement: 115 Degrees
  • Left/Right wig-wag scan:
    +/- 20 degrees
  • Vertical Travel: 18” motorized
  • Horizontal travel: 8”
  • Lateral rotation: +/- 180 degrees

C-arm Dimensions

  • Length: 75.9”
  • Height 69.9”
  • Width: 33”

Workstation Dimensions

  • Width: 27”
  • Height 64”
  • Depth: 27”

Reviews

There are no reviews yet.

Be the first to review “Refurbished OEC 9800”

Your email address will not be published. Required fields are marked *

Refurbished OEC 9800

Quote Request

Scroll to Top